DLMS to Modbus Converter
Original price was: ₹14,000.00.₹9,000.00Current price is: ₹9,000.00.
Features
- Supports reading of Cumulative Parameters, Insta Voltage and Current Values and Meter Serial No.
- RS485/RS232/Optical DLMS to RS485 Modbus converter
- 24V DC Input
- Modbus RS-485 Protocol Interface
- Convenient address selection rotatory switch from 1 – 99 Address for modbus
- Complete range of configurable baud rate settings supported for modbus
- Din Rail mounting
- Product Dimensions – 40mm x 110mm x 80mm (L x W x H)
Application:-
- Modbus, Profibus and DMX applications or any RS485 field bus application
- 5 Volt differential or single ended data lines
- Industrial and building automation
- Solar power monitoring systems
- Industrial data communication systems
Configuration Software
| Part No | UPC-DLMS-RS485 |
|---|---|
| Brand | Veawe |
| Mounting Type | DIN Rail, Wall Mount |
| Dimensions | 40mm x 110mm x 80mm |
| Warranty | 1 Year |
| Country of Origin | Made in India |
You may also like…
Ethernet to RS485 Converter UC-ETH-RS485
Features
- Works with all type of industrial equipments
– PC, PLC, SCADA, HMI, AC/DC Drives, Genset, UPS, Development Kits, etc.
RS485 Rx and Tx light indications for easy visibility and troubleshooting
RJ45 Status light indications, RJ45 built-in 2KV isolation
Easy to use web page configuration option
Unique MAC address
Compact design suitable for both DIN Rail and Wall mount
Support 10/100M, TCP Server, TCP Client, UDP, Httpd Client, Web socket
Supports Transparent Mode data transmission
Supports Modbus TCP to Modbus RTU protocol conversion
ESD and Surge protection for Ethernet, RS485 and Power
Supports all Baud Rates from 300 to 250 kBaud.– varies on cable length
Supports up-to 256 receivers on the bus
– also depends on the other devices connected in the RS485 network
- ESD protection for RS485 pins
– ±15-kV Human-Body Model (HBM)
– ±8-kV IEC1000-4-2, Contact Discharge
– ±15-kV IEC1000-4-2, Air-Gap Discharge
- 1 Year Warranty against any manufacturing defects
Surge Protection Device 24V DC SPD
Three-stage SPD-24V-DC surge protection device meets standard protection against power surges, voltage surges and disturbances with three stages of protection.
Housed in a din rail panel mount case with a protected earth ground.
In order to work properly, it is important to have a good connection in E terminal to solid earth ground. Unknown electronic device failure and misbehave in controller units might be avoided by using SPD-24V-DC
Features:-
Protection provided by high energy MOV and TVS
Internal thermal disconnects
Status indicator input and output
Replaceable modular design, DIN Rail compatible base
Application:–
All types 24V-DC PLC, HMI, etc.,
Where to Use:
Noisy industrial lines like DC inductive load switching
Industrial power panels
Requiring a Load dump feature
open Long DC caballing in panel board
Surge Protection Device RS485 SPD-RS485
Three-stage SPD485 surge protection device meets standard protection against power surges, voltage surges,
common mode line noise and disturbances with three stages of protection and filter each supported with Transient
Voltage Suppressor (TVS).
Housed in a din rail panel mount case with a protected earth ground.
In order to work properly, it is important to have a good connection in E terminal to solid earth ground.
USB to RS485 Converter UC-RS485
*Connecting to Industrial Field buses, remote devices to a latest Computer becomes
difficult due to obsolete of the RS232C ports by Computer Manufactures.
*But with the vast use of equipments with these interfaces needs a connection with PC for monitoring, configuring and working.
*Most of the market available converters are not equipments with proper ESD protection circuits to work longer and with an industry equipment.
*So we have our most suitable converter for both Industrial environment and general usage.
In most case of Windows 10/11 and Linux the driver will be installed automatically when the PC is connected to the Internet.
https://ftdichip.com/wp-content/uploads/2023/09/CDM-v2.12.36.4-WHQL-Certified.zip
Related products
Current Source Simulator Without Display
The Analog Source Generator(0-20mA) will assist
maintenance personnel and integrators in analog input testing
troubleshooting and application development.
This device is handy for testing Sensor data with PLC’s
analog input variants like gas/liquid sensor. Also useful for
measuring data from Pressure sensor, Strain Gauge Sensor,
Temperature Sensor, Level Sensor, Position Sensor etc.
Isolated Analog Signal Converter ±75mV to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : ±75mV DC (Bidirectional Shunt)
Output Signal type : 4-20mA DC (12mA zero center)
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 150V to 10V
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-150V DC
Output Signal type : 0-10V DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 150V to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-150V DC
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 75mV to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-75mV DC (Shunt)
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter Pt 1000
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : Pt 1000
Output Signal type : 0/4 – 20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Signal Isolator 4 20ma
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 4-20mA DC
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
USB to ISO RS485 Converter UC-ISO-RS485
Specification
Isolated RS485 Power up to 1KVrms
Isolated RS485 Signals up to 2.5KVrms
Extended Common mode voltage between A an B ±25V
Works with all type of industrial equipments
– PC, PLC, SCADA, HMI, AC/DC Drives, Genset, UPS, Development Kits, etc.
USB Power, RS485 Rx and Tx light indications for easy visibility and troubleshooting
ESD and Surge protection for USB, RS485 and Power
Supports all Baud Rates from 300 to 250 kBaud.
– varies on cable length
- Supports up-to 256 receivers on the bus
– also depends on the other devices connected in the RS485 network
Very compact size 60mm x 40mm x 20mm
ESD protection for RS485 pins
– ±16-kV Human-Body Model (HBM)
– ±8-kV IEC1000-4-2, Contact Discharge
– ±15-kV IEC1000-4-2, Air-Gap Discharge
- ESD protection for USB
– ±2-kV Human-Body Model (HBM)
– ±200-kV Machine Mode (MM)
– ±500-kV Charged device mode (CDM)
- 1 Year Warranty against any manufacturing defects
In most case of Windows 10/11 and Linux the driver will be installed automatically when the PC is connected to the Internet.
https://ftdichip.com/wp-content/uploads/2023/09/CDM-v2.12.36.4-WHQL-Certified.zip
Reviews
There are no reviews yet.