UIO- 48DI Modbus Module
Original price was: ₹12,000.00.₹10,000.00Current price is: ₹10,000.00.
Product Features
● 24 V DC Input Supply
● 48 PNP Digital Input
● Modbus RS-485 Protocol Interface
● Convenient address selection rotatory switch from 1 – 99 Address
● Dimension – 110 mm x 150 mm x 85 mm
Features
● Four Channel 0 ~ 20mA 12 bit Resolution ADC
● Modbus RS-485 Protocol Interface.
● Individual Channel offset calibration
● Resolution at 0.005 mA
● Convenient address selection rotatory switch from 1 – 99 Address
● Complete range of baud rate settings supported
● Sensor open indication
● Suitable for both Din Rail and Wall Mountable
● Product Dimensions 110mm x 50mm x 55mm (L x W x H)
Default Mode Switch
Default mode is handy when the serial communication setting are forgotten.
Setting the Address switch to 00 will put the device in default mode
Address Set to 00 - Default mode ON
– Slave Address – 1, Baud 19200, 8N1
Address Set to non 00 - Default mode OFF
– As per the saved configuration values.
Note:
No parameter selection is changed just by entering the default mode. All the parameters
remains same including the communication settings unless changed by the master or if there is a
corruption in data error indicated in normal mode the device will try to recover to Factory settings.
This mode can be used to read the present settings and/or change the settings
Sensor Open indication
If Channel 1 or 2 Sensor is not connected value is read as 0.0 mA and corresponding
Discrete Input bit is set.
Diagnostics
Tx LED - Quick Blink Indicates Tx Data in Normal operation
Rx LED - Quick Blink Indicates Rx Data in Normal operation
Power LED - Power Supply Status
Supported Modbus Function Codes
02 – Read Discrete Inputs
03 – Read Holding Registers
04 – Read Input Registers
06 – Write Single Register
16 – Write Multiple Registers
Discrete Inputs (Read Only)
0x1.1 (1.1)
– Unused
0x1.2 (1.2)
– Unused
0x1.3 (1.3)
– Channel 1 Sensor Status.
1 indicates Sensor Open 0 indicates Working
0x1.4 (1.4)
– Channel 2 Sensor Status.
1 indicates Sensor Open 0 indicates Working
0x1.5 (1.5)
– Channel 1 low value alarm status.
1 indicates alarm is on due to low value / 0 indicates value is with in
normal range
0x1.6 (1.6)
– Channel 1 high value alarm status.
1 indicates alarm is on due to high value / 0 indicates value is with in
normal range
0x1.7 (1.7)
– Channel 2 low value alarm status.
1 indicates alarm is on due to low value / 0 indicates value is with in
normal range
0x1.8 (1.8)
– Channel 2 high value alarm status.
1 indicates alarm is on due to high value / 0 indicates value is with in
normal range
| Material |
Wood |
|---|---|
| Height |
79.5 cm |
| Length |
46.5 cm |
You may also like…
Ethernet to RS485 Converter UC-ETH-RS485
Features * Works with all type of industrial equipments – PC, PLC, SCADA, HMI, AC/DC Drives, Genset, UPS, Development Kits, etc. * RS485 Rx and Tx light indications for easy visibility and troubleshooting * RJ45 Status light indications, RJ45 built-in 2KV isolation * User Friendly Configuration Software * Easy to use web page configuration option * Unique MAC address * Compact design suitable for both DIN Rail and Wall mount * Support 10/100M, TCP Server, TCP Client, UDP, Httpd Client, Web socket * Supports Transparent Mode data transmission * Supports Modbus TCP to Modbus RTU protocol conversion * ESD and Surge protection for Ethernet, RS485 and Power * Supports all Baud Rates from 300 to 250 kBaud.– varies on cable length * Supports up-to 256 receivers on the bus – also depends on the other devices connected in the RS485 network * ESD protection for RS485 pins – ±15-kV Human-Body Model (HBM) – ±8-kV IEC1000-4-2, Contact Discharge – ±15-kV IEC1000-4-2, Air-Gap Discharge * 1 Year Warranty against any manufacturing defects
Surge Protection Device RS485 SPD-RS485
Three-stage SPD485 surge protection device meets standard protection against power surges, voltage surges, common mode line noise and disturbances with three stages of protection and filter each supported with Transient Voltage Suppressor (TVS). Housed in a din rail panel mount case with a protected earth ground. In order to work properly, it is important to have a good connection in E terminal to solid earth ground.
USB to RS485 Converter UC-RS485
*Connecting to Industrial Field buses, remote devices to a latest Computer becomes difficult due to obsolete of the RS232C ports by Computer Manufactures.
*But with the vast use of equipments with these interfaces needs a connection with PC for monitoring, configuring and working.
*Most of the market available converters are not equipments with proper ESD protection circuits to work longer and with an industry equipment.
*So we have our most suitable converter for both Industrial environment and general usage.
In most case of Windows 10/11 and Linux the driver will be installed automatically when the PC is connected to the Internet. https://ftdichip.com/wp-content/uploads/2023/09/CDM-v2.12.36.4-WHQL-Certified.zip
Reviews
There are no reviews yet.