Loadcell Amplifier – ±10V
Original price was: ₹5,000.00.₹2,500.00Current price is: ₹2,500.00.
Features & Specification
Suitable for all bridge sensor
Precision excitation supply for the sensor
Compact design suitable for both DIN Rail and
Wall mount
Calibration with zero and span
Lesser than 0.5% noise output for Full scale 0~20mA
1 Year Warranty against any manufacturing defects
Specification
- Suitable for all bridge sensor
- Precision excitation supply for the sensor
- Compact design suitable for both
DIN Rail and wall mount - Calibration with zero and span
- Lesser than 0.5% noise output for Full scale 0~10V
- 1 Year Warranty against any manufacturing defectsefects
Zero Offset and Span Settings
Zero offset –
Connect the load cell sensor without load and and then
adjust the zero offset knob until you get ~0V in the
meter / display
Span offset –
Connect the load cell sensor in full load and then adjust
the span offset knob until you get ~10V in the
meter / display
Electrical characteristics
Input signal type: Load cell sensor with excitation
source
Output signal type: ±10V
Accuracy: Less than +/- 1% @ 25°C ambient temperature
Ripple Noise in output: Less than +/- 0.5%
Responds time: Less than 1 milliSec
ESD protection all input
and output pins:
±15-kV Human-Body Model (HBM)IEC1000-4-
2, Contact Discharge V IEC1000-4-2, Air-Gap
Discharge
Output short circuit
protection: 20mA @ 10V
Input Supply Voltage: 24V DC
Operating temperature: 0 to 85 C
Operating current: 200mA @ 24V DC
Dimension in mm: 110 x 50 x 55
Weight: 100g
| Dimensions | 60mm x 40mm x 20mm |
|---|---|
| Part No | AC-LD-B10 |
You may also like…
Loadcell to Modbus Transmitter
- One Load Cell / Strain Gauge input to Modbus RTU
- Two modes of operation – Scale Mode and Force Mode
- 20-bit resolution analog to digital precision conditioner
- Clean analog front-end designed for industrial environments
- Free software based easy configuration
- Integer and IEEE754 float value support
- Modbus RTU over RS-485
- DIP switch for address selection from 1 to 15
- Wide Supported baud rates from 300 to 115200
- DIN Rail mount support
- Dimensions: 60mm x 50mm x 20mm (L x W x H)
Surge Protection Device 24V DC SPD
Three-stage SPD-24V-DC surge protection device meets standard protection against power surges, voltage surges and disturbances with three stages of protection.
Housed in a din rail panel mount case with a protected earth ground.
In order to work properly, it is important to have a good connection in E terminal to solid earth ground. Unknown electronic device failure and misbehave in controller units might be avoided by using SPD-24V-DC
Features:-
Protection provided by high energy MOV and TVS
Internal thermal disconnects
Status indicator input and output
Replaceable modular design, DIN Rail compatible base
Application:–
All types 24V-DC PLC, HMI, etc.,
Where to Use:
Noisy industrial lines like DC inductive load switching
Industrial power panels
Requiring a Load dump feature
open Long DC caballing in panel board
Related products
Isolated Analog Signal Converter 10V – 10V
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-10V DC
Output Signal type : 0-10V DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 150V to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 70V DC
Output Signal type : 0-20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 150V to 10V
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-150V DC
Output Signal type : 0-10V DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 300V to 10V
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-300V DC
Output Signal type : 0-10V DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 70V to 10V
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-70V DC
Output Signal type : 0-10V DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter K Type
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : K – type
Output Signal type : 0/4 – 20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter Pt 100
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : Pt 100
Output Signal type : 0/4 – 20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter Pt 1000
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : Pt 1000
Output Signal type : 0/4 – 20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Reviews
There are no reviews yet.