Modbus Temperature Transmitter – MIO-DES1
Original price was: ₹3,500.00.₹1,950.00Current price is: ₹1,950.00.
- ● Multiple Digital Sensors support
● Modbus RS-485 Protocol Interface.
● Convenient address selection dip switch from 1 – 15 Address
● Complete range of baud rate settings supported
● Sensor open indication, Analog values in integer and float values
● Product Dimensions 60mm x 50mm x 20mm (L x W x H)
Supports Sensor Types
DS18B20 – Digital temperature sensor upto 4 channels
SHT40 – Digital temperature and humidity sensor
| Material | Wood |
|---|---|
| Height | 79.5 cm |
| Length | 46.5 cm |
You may also like…
Ethernet to RS485 Converter UC-ETH-RS485
Features
* Works with all type of industrial equipments
– PC, PLC, SCADA, HMI, AC/DC Drives, Genset, UPS, Development Kits, etc.
* RS485 Rx and Tx light indications for easy visibility and troubleshooting
* RJ45 Status light indications, RJ45 built-in 2KV isolation
* User Friendly Configuration Software
* Easy to use web page configuration option
* Unique MAC address
* Compact design suitable for both DIN Rail and Wall mount
* Support 10/100M, TCP Server, TCP Client, UDP, Httpd Client, Web socket
* Supports Transparent Mode data transmission
* Supports Modbus TCP to Modbus RTU protocol conversion
* ESD and Surge protection for Ethernet, RS485 and Power
* Supports all Baud Rates from 300 to 250 kBaud.– varies on cable length
* Supports up-to 256 receivers on the bus
– also depends on the other devices connected in the RS485 network
* ESD protection for RS485 pins
– ±15-kV Human-Body Model (HBM)
– ±8-kV IEC1000-4-2, Contact Discharge
– ±15-kV IEC1000-4-2, Air-Gap Discharge
* 1 Year Warranty against any manufacturing defects
Surge Protection Device RS485 SPD-RS485
Three-stage SPD485 surge protection device meets standard protection against power surges, voltage surges,
common mode line noise and disturbances with three stages of protection and filter each supported with Transient
Voltage Suppressor (TVS).
Housed in a din rail panel mount case with a protected earth ground.
In order to work properly, it is important to have a good connection in E terminal to solid earth ground.
USB to RS485 Converter UC-RS485
*Connecting to Industrial Field buses, remote devices to a latest Computer becomes
difficult due to obsolete of the RS232C ports by Computer Manufactures.
*But with the vast use of equipments with these interfaces needs a connection with PC for monitoring, configuring and working.
*Most of the market available converters are not equipments with proper ESD protection circuits to work longer and with an industry equipment.
*So we have our most suitable converter for both Industrial environment and general usage.
In most case of Windows 10/11 and Linux the driver will be installed automatically when the PC is connected to the Internet.
https://ftdichip.com/wp-content/uploads/2023/09/CDM-v2.12.36.4-WHQL-Certified.zip
Related products
2 Channel Isolated Digital Input Modbus RTU RS485 Module
- ● Multiple Digital Sensors support
● Modbus RS-485 Protocol Interface.
● Convenient address selection dip switch from 1 – 15 Address
● Complete range of baud rate settings supported
● Sensor open indication, Analog values in integer and float values
● Product Dimensions 60mm x 50mm x 20mm (L x W x H)
8 CH 20mA Remote Input Module UIO-8IN-20mA
Key Features
- 8 Channel 0–20mA Analog Inputs
- 16-bit analog resolution
- Factory calibrated accuracy: ± 0.1% from upper-range
- Raw analog value resolution in steps of 0.001mA
- Sensor open / broken wire indication
- Configurable individual alarms indication
- Retentive alarm counters on power cycle
- Individual channel offset and gain calibration
- Integer and IEEE754 float value support
- Modbus RTU over Isolated RS-485
- Modbus RTU remote write master mode
- Easy to use free ModViz software
- Rotary address switch for address selection from 1 to 99
- Wide Supported baud rates from 300 to 115200
- DIN rail mountable
- Dimensions: 110mm × 50mm × 55mm
Loadcell to Modbus Transmitter
- One Load Cell / Strain Gauge input to Modbus RTU
- Two modes of operation – Scale Mode and Force Mode
- 20-bit resolution analog to digital precision conditioner
- Clean analog front-end designed for industrial environments
- Free software based easy configuration
- Integer and IEEE754 float value support
- Modbus RTU over RS-485
- DIP switch for address selection from 1 to 15
- Wide Supported baud rates from 300 to 115200
- DIN Rail mount support
- Dimensions: 60mm x 50mm x 20mm (L x W x H)
ModViz
ModViz – Modbus Configuration & Visualization Tool for Veawe I/O Modules
ModViz is a powerful yet simple configuration and visualization tool designed to work seamlessly with Veawe Modbus I/O modules. It enables engineers, system integrators, and technicians to quickly configure, monitor, and test field devices through an intuitive graphical interface.
UIO- 4DI 4DO Modbus Module
- 4 digital inputs and 4 digital outputs with LED indication for all IO’s
- RS485 interface output with Modbus RTU Slave
- Suitable for all types of Industrial Machine Automation, IoT, IO Expansion, Remote monitoring
- ● Convenient address selection rotatory switch from 1 – 99 Address
- ● Complete range of baud rate settings supported
- ● Suitable for both Din Rail and Wall Mountable
● Product Dimensions 110mm x 50mm x 55mm (L x W x H)
Reviews
There are no reviews yet.