Loadcell Amplifier – 0-10V
₹2,500.00
Features & Specification
Suitable for all bridge sensor
Precision excitation supply for the sensor
Compact design suitable for both
DIN Rail and wall mount
Calibration with zero and span
Lesser than 0.5% noise output for Full scale 0~10V
1 Year Warranty against any manufacturing defects
Specification
- Suitable for all bridge sensor
- Precision excitation supply for the sensor
- Compact design suitable for both
DIN Rail and wall mount - Calibration with zero and span
- Lesser than 0.5% noise output for Full scale 0~10V
- 1 Year Warranty against any
- Zero Offset and Span Settings
Zero offset –
Connect the load cell sensor without load and and then
adjust the zero offset knob until you get ~0V in the
meter / display
Span offset –
Connect the load cell sensor in full load and then adjust
the span offset knob until you get ~10V in the
meter / display manufacturing defects
Electrical characteristics
Input signal type: Load cell sensor with excitation
source
Output signal type: 0-10v Accuracy: Less than +/- 1% @ 25°C ambient temperature
Ripple Noise in output: Less than +/- 0.5%
Responds time: Less than 1 milliSec
ESD protection all input
and output pins:
±15-kV Human-Body Model (HBM)IEC1000-4-
2, Contact Discharge V IEC1000-4-2, Air-Gap
Discharge
Output short circuit
protection: 20mA @ 10V
Input Supply Voltage: 24V DC
Operating temperature: 0 to 85 C
Operating current: 200mA @ 24V DC
Dimension in mm: 110 x 50 x 55
Weight: 100g
| Dimensions | 60mm x 40mm x 20mm |
|---|---|
| Part No | AC-LD-10 |
| Brand | Veawe |
| Mounting Type | DIN Rail, Wall Mount |
| Warranty | 1 Year |
| Country of Origin | Made in India |
You may also like…
Loadcell to Modbus Transmitter
- One Load Cell / Strain Gauge input to Modbus RTU
- Two modes of operation – Scale Mode and Force Mode
- 20-bit resolution analog to digital precision conditioner
- Clean analog front-end designed for industrial environments
- Free software based easy configuration
- Integer and IEEE754 float value support
- Modbus RTU over RS-485
- DIP switch for address selection from 1 to 15
- Wide Supported baud rates from 300 to 115200
- DIN Rail mount support
- Dimensions: 60mm x 50mm x 20mm (L x W x H)
Voltage Source Simulator 0-10V (USS10V24V-D)
The Analog Source Generator(0-10v) will assist
maintenance personnel and integrators in analog input testing
troubleshooting and application development.
This device is handy for testing Sensor data with PLC’s
analog input variants like gas/liquid sensor. Also useful for
measuring data from Pressure sensor, Strain Gauge Sensor,
Temperature Sensor, Level Sensor, Position Sensor etc..,
SPECIFICATION
Functionality
Perfect 0-10v Signal Source Generator
Power Supply
24V DC External
Display
4 digit Segment display
Voltage Output
Output Range 0-10V DC
Output Accuracy ±1% of full scale
Load range 100mA Max
Protection
Input Reverse Polarity , Output Short Circuit Protection
DIMENSION
Product size 48x48x90mm.
Preffered Panel cut out 45x45mm.
Related products
Isolated Analog Signal Converter 10V – 10V
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-10V DC
Output Signal type : 0-10V DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 300V to 10V
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-300V DC
Output Signal type : 0-10V DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 75mV to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-75mV DC (Shunt)
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter Pt 1000
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : Pt 1000
Output Signal type : 0/4 – 20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter Resistance to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : Ω
Output Signal type : 0/4 – 20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated RS232 To RS485
Isolated RS485 Signals up to 2.5Vrms
Isolated RS485 Power up to 1KVrms.
Supports Auto-Direction Control. No flow
control signal required.
- Supports all Baud Rates from 300 to 250
kBaud.
– actual baud rate varies on the cable length
– also depends on the other devices
connected in the RS485 network
- Works with all type of industrial equipments
– PC, PLC, SCADA, HMI, AC/DC Drives,
Genset, UPS, Development Kits, etc.
- RS485 Rx and Tx light indications for easy
visibility and troubleshooting
- ESD protection for RS232 and RS485 pins
– ±15-kV Human-Body Model (HBM)
– ±8-kV IEC1000-4-2, Contact Discharge
– ±15-kV IEC1000-4-2, Air-Gap Discharge
- Compact design suitable for both DIN Rail and
Wall mount
Dimension in mm – 110 x 74 x 35
1 Year Warranty against any manufacturing
defects
RS485 to RS485 Repeater UC-RS485-RS485
Connecting to Industrial Field buses, remote devices to a latest Computer becomes
difficult due to obsolete of the RS232C ports by Computer Manufactures. But with the vast
use of equipments with these interfaces needs a connection with PC for monitoring,
configuring and working. Most of the market available converters are not equipments with
proper ESD protection circuits to work longer and with an industry equipment. So we have our
most suitable converter for both Industrial environment and general usage.
Supports Auto-Direction Control.
- Supports all Baud Rates from 300 to 250 kBaud.
– actual baud rate varies on the cable length
- Supports up-to 256 receivers on the bus
– also depends on the other devices connected in
the RS485 network
- Works with all type of industrial equipments
– PC, PLC, SCADA, HMI, AC/DC Drives,
Genset, UPS, Development Kits, etc.
- RS485 Rx and Tx light indications for easy visibility
and troubleshooting
- ESD protection for and RS485 pins at both ends
Reviews
There are no reviews yet.