2 Channel Analog Input Modbus RTU RS485 Module
- One 0 – 20mA and one 0 – 36V DC Analog Inputs
- 16-bit analog resolution
- Modbus RS-485 Protocol Interface.
- Integer and IEEE754 float value support
- Offset and Gain support
- Convenient address selection dip switch from 1 – 15 Address
- Complete range of baud rate settings supported
- Sensor open indication, Analog values in integer and float values
- DIN Rail mount support
- Product Dimensions 60mm x 50mm x 20mm (L x W x H)
4 Channel 20mA Modbus UIO-4IN-20mA
4-20mA Surge Protection Device SPD 4 to 20mA
- Three-stage SPD-20mA surge protection device meets standard
protection against power surges, voltage surges and
disturbances with three stages of protection.
- Housed in a din rail panel mount case with a protected earth
ground.
- In order to work properly, it is important to have a good
connection in E terminal to solid earth ground.
- Unknown electronic device failure and misbehave in controller
units might be avoided by using SPD-20mA
Features:
Protection provided by high energy MOV and TVS
Replaceable modular design, DIN Rail compatible base
All types of 20mA current loop devices, Also works for HART
interface
Where to Use:
*Noisy industrial lines like DC inductive load switching
*Industrial power panels
*Solar plants
*Gas stations
8 Channel 20mA Modbus Input Module UIO-8IN-20mA
-
Key Features
- 8 Channel 0–20mA Analog Inputs
- 16-bit analog resolution
- Factory calibrated accuracy: ± 0.1% from upper-range
- Raw analog value resolution in steps of 0.001mA
- Sensor open / broken wire indication
- Configurable individual alarms indication
- Retentive alarm counters on power cycle
- Individual channel offset and gain calibration
- Integer and IEEE754 float value support
- Modbus RTU over Isolated RS-485
- Modbus RTU remote write master mode
- Easy to use free ModViz software
- Rotary address switch for address selection from 1 to 99
- Wide Supported baud rates from 300 to 115200
- DIN rail mountable
- Dimensions: 110mm × 50mm × 55mm
8 Channel 4x 20mA + 4x 10V Modbus Input Module UIO-8IN-VI
Key Features
- 4 Channel 0–20mA Analog Inputs (CH1–CH4)
- 4 Channel 0–10V Analog Inputs (CH5–CH8)
- 16-bit analog resolution
- Factory calibrated accuracy: ± 0.1% from upper-range
- Raw analog value resolution in steps of 0.001mA (CH1–CH4) & 0.001V (CH5–CH8)
- Sensor open / broken wire indication
- Configurable individual alarms indication
- Retentive alarm counters on power cycle
- Individual channel offset and gain calibration
- Integer and IEEE754 float value support
- Modbus RTU over Isolated RS-485
- Modbus RTU remote write master mode
- Easy to use free ModViz software
- Rotary address switch for address selection from 1 to 99
- Wide Supported baud rates from 300 to 115200
- DIN rail mountable
- Dimensions: 110mm × 50mm × 55mm
Isolated 20mA splitter AC-20mA-2
Isolated Analog Signal Converter ±75mV to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : ±75mV DC (Bidirectional Shunt)
Output Signal type : 4-20mA DC (12mA zero center)
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 150V to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-150V DC
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 70V to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-70V DC
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 75mV to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-75mV DC (Shunt)
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter J Type
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : J – type
Output Signal type : 0/4 – 20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter K Type
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : K – type
Output Signal type : 0/4 – 20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC