Loadcell Amplifier – ±10V
Original price was: ₹5,000.00.₹2,500.00Current price is: ₹2,500.00.
Features & Specification
Suitable for all bridge sensor
Precision excitation supply for the sensor
Compact design suitable for both DIN Rail and
Wall mount
Calibration with zero and span
Lesser than 0.5% noise output for Full scale 0~20mA
1 Year Warranty against any manufacturing defects
Specification
- Suitable for all bridge sensor
- Precision excitation supply for the sensor
- Compact design suitable for both
DIN Rail and wall mount - Calibration with zero and span
- Lesser than 0.5% noise output for Full scale 0~10V
- 1 Year Warranty against any manufacturing defectsefects
Zero Offset and Span Settings
Zero offset –
Connect the load cell sensor without load and and then
adjust the zero offset knob until you get ~0V in the
meter / display
Span offset –
Connect the load cell sensor in full load and then adjust
the span offset knob until you get ~10V in the
meter / display
Electrical characteristics
Input signal type: Load cell sensor with excitation
source
Output signal type: ±10V
Accuracy: Less than +/- 1% @ 25°C ambient temperature
Ripple Noise in output: Less than +/- 0.5%
Responds time: Less than 1 milliSec
ESD protection all input
and output pins:
±15-kV Human-Body Model (HBM)IEC1000-4-
2, Contact Discharge V IEC1000-4-2, Air-Gap
Discharge
Output short circuit
protection: 20mA @ 10V
Input Supply Voltage: 24V DC
Operating temperature: 0 to 85 C
Operating current: 200mA @ 24V DC
Dimension in mm: 110 x 50 x 55
Weight: 100g
| Dimensions | 60mm x 40mm x 20mm |
|---|---|
| Part No | AC-LD-B10 |
| Brand | Veawe |
| Mounting Type | DIN Rail, Wall Mount |
| Warranty | 1 Year |
| Country of Origin | Made in India |
You may also like…
Loadcell to Modbus Transmitter
- One Load Cell / Strain Gauge input to Modbus RTU
- Two modes of operation – Scale Mode and Force Mode
- 20-bit resolution analog to digital precision conditioner
- Clean analog front-end designed for industrial environments
- Free software based easy configuration
- Integer and IEEE754 float value support
- Modbus RTU over RS-485
- DIP switch for address selection from 1 to 15
- Wide Supported baud rates from 300 to 115200
- DIN Rail mount support
- Dimensions: 60mm x 50mm x 20mm (L x W x H)
Surge Protection Device 24V DC SPD
Three-stage SPD-24V-DC surge protection device meets standard protection against power surges, voltage surges and disturbances with three stages of protection.
Housed in a din rail panel mount case with a protected earth ground.
In order to work properly, it is important to have a good connection in E terminal to solid earth ground. Unknown electronic device failure and misbehave in controller units might be avoided by using SPD-24V-DC
Features:-
Protection provided by high energy MOV and TVS
Internal thermal disconnects
Status indicator input and output
Replaceable modular design, DIN Rail compatible base
Application:–
All types 24V-DC PLC, HMI, etc.,
Where to Use:
Noisy industrial lines like DC inductive load switching
Industrial power panels
Requiring a Load dump feature
open Long DC caballing in panel board
Related products
Isolated Analog Signal Converter 10V – 10V
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-10V DC
Output Signal type : 0-10V DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 300V to 10V
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-300V DC
Output Signal type : 0-10V DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 70V to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-70V DC
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter Pt 100
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : Pt 100
Output Signal type : 0/4 – 20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter Resistance to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : Ω
Output Signal type : 0/4 – 20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated RS485 To RS485
Features and Specification
* Isolated RS485 Signals up to 2.5KVrms
* Isolated RS485 Power up to 1KVrms.
* Supports Auto-Direction Control. No flow
control signal required.
– actual baud rate varies on the cable length
– also depends on the other devices connected
in the RS485 network
* Works with all type of industrial equipment
– PC, PLC, SCADA, HMI, AC/DC Drives,
Genset, UPS, Development Kits, etc.
* RS485 Rx and Tx light indications for easy
visibility and troubleshooting
* ESD protection for both RS485 pins
– ±15-kV Human-Body Model (HBM)
– ±8-kV IEC1000-4-2, Contact Discharge
– ±15-kV IEC1000-4-2, Air-Gap Discharge
* Compact design suitable for both DIN Rail and Wall mount
* Dimension in mm – 110 x 74 x 35
* 1 Year Warranty against any manufacturing
defects
RS232 to RS485 Converter
Connecting to Industrial Field buses, remote devices to a latest Computer becomes
difficult due to obsolete of the RS232C ports by Computer Manufactures. But with the vast
use of equipments with these interfaces needs a connection with PC for monitoring,
configuring and working. Most of the market available converters are not equipments with
proper ESD protection circuits to work longer and with an industry equipment. So we have our
most suitable converter for both Industrial environment and general usage.
Supports Auto-Direction Control. No flow control signal required.
Supports all Baud Rates from 300 to 250 kBaud.
– actual baud rate varies on the cable length
- Supports up-to 256 receivers on the bus
– also depends on the other devices connected in the RS485 network
- Works with all type of industrial equipments
– PC, PLC, SCADA, HMI, AC/DC Drives, Genset, UPS, Development Kits, etc.
RS485 Rx and Tx light indications for easy visibility and troubleshooting
ESD protection for RS232 and RS485 pins
– ±15-kV Human-Body Model (HBM)
– ±8-kV IEC1000-4-2, Contact Discharge
– ±15-kV IEC1000-4-2, Air-Gap Discharge
Very compact size 60mm x 40mm x 20mm
1 Year Warranty against any manufacturing defects
Signal Isolator 4 20ma
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 4-20mA DC
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Reviews
There are no reviews yet.