Signal Isolator 4 20ma
Original price was: ₹4,000.00.₹2,250.00Current price is: ₹2,250.00.
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 4-20mA DC
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Application:-
- Ground loop elimination between remote field transmitters and control room equipment
- Protection of PLC, DCS, and SCADA analog input modules from voltage spikes and surge currents
- Industrial Automation & Process Control signal isolation
- Signal conditioning in high electrical noise environments
- Control panel building and field instrumentation wiring
Key Features:-
- Current Loop Isolation: Eliminates ground loops, common-mode noise, and electrical interference
- 2-Way Galvanic Isolation up to 1 kV RMS optical and magnetic isolation
- True Analog Signal Isolation – Preserves loop dynamics with a pure linear amplifier stage
- No PWM conversion or digital reconstruction artifacts
- Fast dynamic response with minimal signal processing delay (< 50 ms)
- High noise immunity against industrial electrical interference
- High linear conversion accuracy (< ±0.5% F.S.)
- Compact design suitable for both 35 mm DIN Rail and wall mount
- 1 Year Warranty against any manufacturing defects
- Customization of input and output current spans available on order
Dimension in mm: 110 x 74 x 22
Weight: 100g
| Part No | AC-420-420 |
|---|---|
| Brand | Veawe |
| Signal Type | Current Loop Isolator |
| Input Signal Type | 4-20mA DC |
| Output Signal | 4-20mA DC |
| Supply Voltage | 24V DC (15 ~ 28V DC) |
| Mounting Type | DIN Rail, Wall Mount |
| Isolation | 1000 V RMS |
| Output Accuracy | < ±0.5% F.S. |
| Protection | Reverse Polarity, TVS Surge Clamping |
| Warranty | 1 Year |
| Country of Origin | Made in India |
| Dimensions | 110mm x 74mm x 22mm |
You may also like…
4-20mA Surge Protection Device SPD 4 to 20mA
- Three-stage SPD-20mA surge protection device meets standard
protection against power surges, voltage surges and
disturbances with three stages of protection.
- Housed in a din rail panel mount case with a protected earth
ground.
- In order to work properly, it is important to have a good
connection in E terminal to solid earth ground.
- Unknown electronic device failure and misbehave in controller
units might be avoided by using SPD-20mA
Features:
Protection provided by high energy MOV and TVS
Replaceable modular design, DIN Rail compatible base
All types of 20mA current loop devices, Also works for HART
interface
Where to Use:
*Noisy industrial lines like DC inductive load switching
*Industrial power panels
*Solar plants
*Gas stations
Current Source Simulator 0/4 to 20mA
The Analog Source Generator(0-20mA) will assist
maintenance personnel and integrators in analog input testing
troubleshooting and application development.
This device is handy for testing Sensor data with PLC’s
analog input variants like gas/liquid sensor. Also useful for
measuring data from Pressure sensor, Strain Gauge Sensor,
Temperature Sensor, Level Sensor, Position Sensor etc.
Surge Protection Device 24V DC SPD
Three-stage SPD-24V-DC surge protection device meets standard protection against power surges, voltage surges and disturbances with three stages of protection.
Housed in a din rail panel mount case with a protected earth ground.
In order to work properly, it is important to have a good connection in E terminal to solid earth ground. Unknown electronic device failure and misbehave in controller units might be avoided by using SPD-24V-DC
Features:-
Protection provided by high energy MOV and TVS
Internal thermal disconnects
Status indicator input and output
Replaceable modular design, DIN Rail compatible base
Application:–
All types 24V-DC PLC, HMI, etc.,
Where to Use:
Noisy industrial lines like DC inductive load switching
Industrial power panels
Requiring a Load dump feature
open Long DC caballing in panel board
Related products
Current Source Simulator Without Display
The Analog Source Generator(0-20mA) will assist
maintenance personnel and integrators in analog input testing
troubleshooting and application development.
This device is handy for testing Sensor data with PLC’s
analog input variants like gas/liquid sensor. Also useful for
measuring data from Pressure sensor, Strain Gauge Sensor,
Temperature Sensor, Level Sensor, Position Sensor etc.
DLMS to Modbus Converter
Features
- Supports reading of Cumulative Parameters, Insta Voltage and Current Values and Meter Serial No.
- RS485/RS232/Optical DLMS to RS485 Modbus converter
- 24V DC Input
- Modbus RS-485 Protocol Interface
- Convenient address selection rotatory switch from 1 – 99 Address for modbus
- Complete range of configurable baud rate settings supported for modbus
- Din Rail mounting
- Product Dimensions – 40mm x 110mm x 80mm (L x W x H)
Isolated Analog Signal Converter 150V to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-150V DC
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter 70V to 20mA
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : 0-70V DC
Output Signal type : 4-20mA DC
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated Analog Signal Converter K Type
Features:-
2 Way isolation up to 1KVrms
Compact design suitable for both DIN Rail and wall
mount
1 Year Warranty against any manufacturing defects.
Customizable Input voltages available on order
Input Signal type : K – type
Output Signal type : 0/4 – 20mA
Accuracy : Less than +/- 1% @ 25°C ambient temperature
Input Supply Voltage : 24V DC
Isolated RS485 To RS485
Features and Specification
* Isolated RS485 Signals up to 2.5KVrms
* Isolated RS485 Power up to 1KVrms.
* Supports Auto-Direction Control. No flow
control signal required.
– actual baud rate varies on the cable length
– also depends on the other devices connected
in the RS485 network
* Works with all type of industrial equipment
– PC, PLC, SCADA, HMI, AC/DC Drives,
Genset, UPS, Development Kits, etc.
* RS485 Rx and Tx light indications for easy
visibility and troubleshooting
* ESD protection for both RS485 pins
– ±15-kV Human-Body Model (HBM)
– ±8-kV IEC1000-4-2, Contact Discharge
– ±15-kV IEC1000-4-2, Air-Gap Discharge
* Compact design suitable for both DIN Rail and Wall mount
* Dimension in mm – 110 x 74 x 35
* 1 Year Warranty against any manufacturing
defects
RS232 to RS485 Converter
Connecting to Industrial Field buses, remote devices to a latest Computer becomes
difficult due to obsolete of the RS232C ports by Computer Manufactures. But with the vast
use of equipments with these interfaces needs a connection with PC for monitoring,
configuring and working. Most of the market available converters are not equipments with
proper ESD protection circuits to work longer and with an industry equipment. So we have our
most suitable converter for both Industrial environment and general usage.
Supports Auto-Direction Control. No flow control signal required.
Supports all Baud Rates from 300 to 250 kBaud.
– actual baud rate varies on the cable length
- Supports up-to 256 receivers on the bus
– also depends on the other devices connected in the RS485 network
- Works with all type of industrial equipments
– PC, PLC, SCADA, HMI, AC/DC Drives, Genset, UPS, Development Kits, etc.
RS485 Rx and Tx light indications for easy visibility and troubleshooting
ESD protection for RS232 and RS485 pins
– ±15-kV Human-Body Model (HBM)
– ±8-kV IEC1000-4-2, Contact Discharge
– ±15-kV IEC1000-4-2, Air-Gap Discharge
Very compact size 60mm x 40mm x 20mm
1 Year Warranty against any manufacturing defects
USB to ISO RS485 Converter UC-ISO-RS485
Specification
Isolated RS485 Power up to 1KVrms
Isolated RS485 Signals up to 2.5KVrms
Extended Common mode voltage between A an B ±25V
Works with all type of industrial equipments
– PC, PLC, SCADA, HMI, AC/DC Drives, Genset, UPS, Development Kits, etc.
USB Power, RS485 Rx and Tx light indications for easy visibility and troubleshooting
ESD and Surge protection for USB, RS485 and Power
Supports all Baud Rates from 300 to 250 kBaud.
– varies on cable length
- Supports up-to 256 receivers on the bus
– also depends on the other devices connected in the RS485 network
Very compact size 60mm x 40mm x 20mm
ESD protection for RS485 pins
– ±16-kV Human-Body Model (HBM)
– ±8-kV IEC1000-4-2, Contact Discharge
– ±15-kV IEC1000-4-2, Air-Gap Discharge
- ESD protection for USB
– ±2-kV Human-Body Model (HBM)
– ±200-kV Machine Mode (MM)
– ±500-kV Charged device mode (CDM)
- 1 Year Warranty against any manufacturing defects
In most case of Windows 10/11 and Linux the driver will be installed automatically when the PC is connected to the Internet.
https://ftdichip.com/wp-content/uploads/2023/09/CDM-v2.12.36.4-WHQL-Certified.zip
Reviews
There are no reviews yet.